Haltech Nexus S3 Plug 'n' Play Adapter faisceau Kit - Nissan Silvia S15
Réf. HT-213317 — Gamme Plug and Play
Description
Haltech's Nexus S3 is the successor to the acclaimed Elite 2500, offering un serious upgrade in performance et functionality. The S3 combines all the classic functionality of the Elite 2500 avec new Caractéristiques et the superior processing power of the successful Nexus platform
8 x peak/hold injector drivers (can be used as low side drive Sorties)
8 x low current ignition Sorties (can be used as low side drive Sorties)
6 x low side drive Sorties, PWM capable (DPOs)
4 x push-pull / half bridge Sorties (8A, PWM capable), eg pour electronic throttle
1 x ECR output
11 x 0-5V analog Entrées avec redundancy pour electronic throttle et switchable 5V pullup
Trigger et home Entrées avec differential Entrées, adjustable thresholds et glitch filters
6 x synchronous pulsed Entrées, zero crossing or adjustable thresholds - cam sensor Entrées, frequency Entrées or 0-5V analog Entrées
1 x on-board contrôleur large bande, supporting NTK et LSU4.9
1 x on-board 4 bar MAP sensor
2 x CAN ports avec switchable termination
Onboard enregistrement de données - Up to 300 channels of logging at sample rates up to 1ms (1kHz) avec 128MB of internal memory
If you are using un factory harness et are after an easy ECU upgrade, take un look at Haltech connecteur 'n' Play Adapter Kits. These adapters connecteur directly into your Haltech ECU et have un set of factory connectors on the other side which connecteur straight into the factory harness
A simple Haltech connecteur 'n' Play product that allows you to be up et running in just un few hours
The quick start guide will walk you through installation of the Haltech connecteur 'n' Play adapter into your vehicle
Caractéristiques
- ECU Caractéristiques
- Controlled via NSP (Nexus Software Programmer)
- apprentissage long terme
- contrôle moteur pas à pas
- 4D contrôle de pression de suralimentation en boucle fermée
- Closed Loop CO2 Control
- Rotational Idle
- launch control
- contrôle de traction
- anti-lag
- Dual contrôle cliquetis
- contrôle transbrake
- chronomètre course
- Multi Stage Fuel Injection
- Multi-level Engine Protection
- 6 Stage Nitrous Control
- 4-sensor variable cam control
- Intake Air Bleed Control
- Flat Shift Control
- Shock Travel & Ride Height Control
- Advanced Torque Management
- On-board Wi-Fi
- On-board datalogging (128MB)
- AUTOMATIC TRANSMISSION CONTROL
- Ford AODE/4R70W
- GM 4L60E
- GM 4L80E
- Toyota A340E
- Lenco
- Liberty
- This harness when installed in conjunction avec un Haltech Nexus S3 ECU opens the door to virtually limitless performance modification et tuning of your vehicle
- Fully programmable systems allow you to extract all the performance from your engine by delivering precisely the required amount of fuel et ignition timing that your engine requires pour maximum output under all operating conditions
Spécifications
- Référence: HT-213317
- Catégorie: 180SX Type X
- Poids indicatif: 1986 g
- UPC: 9356450015738
- Prix HT catalogue: 2108.33 EUR
Compatibilité
- connecteur ‘n’ Play replacement of the factory ECU pour Nissan 200SX/Silvia S15 (Australian Delivered et JDM) 200SX/Silvia S14A S2 “KOUKI” 180SX S13 Rev 3 “Type X” 1996 onwards Pulsar N15 et N14 SSS et GTI-R Micra K11 (CG13DE) Manual transmissions […]